Meco 6212S00T91 Bedienungsanleitung

For Outdoor Household Use Only. Not for Commercial Use.Need Help? Need to Register Your Grill? Looking for Aussie Parts & Accessories?Visit us onl

10Step 7 (Model 6212)Wheel AssemblyPlace the Tank Support between the Left Legs so the holes in the end align with the holes in the legs with the fla

11Step 9Drip Cup Wire AssemblySlide the Drip Cup Wire down through the small hole in the center of the bottom of the grill Bowl. (This must be done be

12Tank Heat ShieldStep 10Main Burner AssemblyA. Slide the burner tubes down through the indicated holes in the bowl and align the holes in the burner

131/4-20 x .39” Bolt4 pcsStep 11Bowl to Cart AssemblyPlace the Bowl Supports on top of the U-Frames, aligning the holes. Attach the Bowl to the cart w

14Step 13Control Panel AssemblyInsert the Control Panel between the front legs and aligning the holes in the ends of the Control Panel with the holes

15CStep 14A. Main Burner Electrode AssemblyInsert small end of Electrode Wire down through the hole in the Bowl in front of the main burner until flan

16Step 15Side Table AssemblyPlace the Side Table flanges with holes around the outside of the U-Frame and align the holes. Insert a 1/4-20 x 1.2” Stai

17Step 17Hood Handle AssemblyModel 6212: Attach the Hood Handle to the Hood with 2) 1/4-20 x .39” Bolts and Fiber Washers. Place Heat Baffles between

18To reduce the risk of a laceration hazard:• Wear protective gloves when installing warming rack. Hood and Bowl edges could be sharp.CAUTION!Step 19F

19Tank Blocking Wire1To reduce the risk of serious bodily injury or death from fire or explosion:Never remove guards or devices to prevent storage of

2To reduce the risk of a laceration hazard, wear protective gloves when handling parts that have sharp edges.CAUTION!Phillips ScrewdriverTools Require

20Step 22Drip Cup AssemblyInsert the Drip Cup into the hanger wire underneath the grill bowl. Step 23Battery Installation (6512 only)Unscrew Igniter C

21Connecting/Disconnecting the GasUsing GasCarbon Monoxide Hazard• This appliance can produce carbon monoxide which has no odor. Using it in an enclo

22LP Hose and RegulatorTo reduce the risk of serious bodily injury or death from fire or explosion:• Clean and inspect the gas hose/regulator before e

23Before Using Your LP Gas GrillInstallation CodesTo reduce the risk of serious bodily injury or death from fire or explosion:• This installation must

24How to Perform A Leak Test “FIRST TIME USE” and as requiredSupplies Needed for a Leak Test:• Clean paint brush• Water• Dish washing liquid1. Use an

256. If “growing” bubbles appear on any of the connection points, you have detected a gas leak. Immediately close the LP Gas Cylinder valve by turning

26Lighting the Grill Using the Ignitor (continued)1. Open the Hood.2. IMPORTANT: Make sure Control Knobs are turned “Off.” (Fig. 4)3. Turn the LP Gas

27Manually Lighting the GrillTo reduce the risk of serious bodily injury or death from fire or explosion:• Open Hood before lighting the grill to prev

28Cooking On the Gas GrillTo reduce the risk of serious bodily injury or death from fire, explosion or burn hazard:• Never use charcoal or lighter flu

29Roasting (Indirect Method)To reduce the risk of burns from flame rollout or the hot air and steam trapped inside:• Open the Hood carefully when roas

3ContentsPreparation for Assembly ...3Parts IdentificationParts Illustration ...

30Care and MaintenanceCleaning the GrillRegularly clean your LP gas grill between uses and especially after extended periods of storage. Ensure the gr

31Should you notice that your Burner(s) are getting hard to light or the flame is not as hot as it once was, refer to the “How to Clean your Burners”

326. Check the Gas Collector Box to verify that there is a 3/16” gap between the electrode tip and the top flange of the box as shown in Fig. 12.NOTE:

33EmergenciesProblemGas leaking from cracked/cut/burned hoseGas leaking from LP Gas CylinderGas leaking from LP Gas Cylinder valveGas leaking between

34TroubleshootingProblemBurners will not light using a matchLow flame or low heatFlames blow outPossible CauseRegulator coupling nut is not fully conn

35ProblemFlare upPersistent grease fireUnable to fill LP tankHumming or whistling from regulatorPossible CauseGrease build-upExcessive fat in meatGrea

36Limited WarrantyMECO CORPORATION - LIMITED WARRANTYThis product is warranted to the original consumer purchaser against defects in material and work

4Parts Illustration - Model 6212S00T91 / 6512S0DT9112A7151091617242629A3032566A8111213181920A21222327283143A33NOTE:

5If you need replacement parts, refer to the Parts Illustrations to find the exact parts you need. If you have any questions or need help, contact Cus

6Assembly InstructionsStep 1Frame IdentificationIdentify parts and lay on floor as shown. Parts are named for their assembled position on the grill. T

7Step 2Shroud to Leg AssemblyThe next 2 steps are best performed on a smooth level surface (and/or with the help of a second person) P

8Threaded Insert1/4-20 x 1.1” BoltTank Side BraceLeft Leg1/4-20 x .39”Step 4Tank Side Brace & Top Crossbrace AssemblyA. Place the Tank Side Brace

9ABAB4 - 1/4-20 x .39” Bolt2 - 1/4-20 x 1.1” BoltStep 5Crossbrace & Right Tube Brace AssemblyA. Assemble one Crossbrace to the inside of the back