Meco BUSHMAN 7710.8.641 Bedienungsanleitung

LP Gas GrillAssembly and Use Manual for: Bushman BushmanbyFor Customer Service, call 1-800-251-7558 or visit our web site at www.aussiegrills.comFOR

10STEP - 8 Mounting Hood/ Bowl Hinges•Insert M6 x 15mm Bolt through Hood Hinge and Fiber Washer and into hole in back side of GrillHood as shown. Inst

11STEP 9 - Attach Hood•Align Hood Hinge tabs with Bottom Hinge tabs and insert Hinge Pins from outside. Secure eachHinge Pin with Cotter Pin as shown.

To reduce the risk of a laceration hazard, wear protective gloves when handling parts that have sharp edges.STEP 10 - Attach Hood Handle & Handle

13STEP 14 - Assemble Side TablesStep 15 - Install Privacy Panel•Slide 8 side table spacers onto 8M6 x 45 mm screws.•Insert M6 x 45mm screws andside ta

14STEP 16 - Insert Drip Cup•Insert drip cup into hanger clip underneath grill bowl.Step 17 - Attach LP CylinderDrip Cup1. Loosen wingbolts on cylinder

OPERATING AND MAINTAINING YOUR GAS GRILLGAS, CYLINDER, HOSE ANDREGULATOR INFORMATIONThis LP gas grill was designed to use propane gas. Propanecylinder

· Never connect or disconnect LP gas cylinder or fittings while grill is in use or is hot. · When the LP gas cylinder is connected, the grill must be

· Always perform a leak test before each use.· Leak test must be performed in a well ventilated area. · Never perform a leak test on a grill while in

· Wash the porcelain or chrome coated Cooking Gridswith a mixture of hot water and baking soda. · Empty the grease cup after each cooking session so

· Open Hood before lighting the grill to prevent an explosion from gas build-up. · Always inspect the gas hose and regulatorassembly before each use.

2IMPORTANT SAFEGUARDSFAILURE TO FOLLOW THESE SAFEGUARDS COULD RESULT IN DEATH, SERIOUSBODILY INJURY, AND/OR PROPERTY LOSS. READ AND FOLLOW ALL INSTRUC

Your burner has been preset by the manufacturer for opti-mal flame performance. A blue flame, possibly with a smallyellow tip, is the result of the op

Most residue on the Cooking Grids can be cleaned with abaking soda and water solution. For stubborn stains, use anonabrasive scouring powder. Do not u

Remove and wash the Flavor Activator Rin order to keep itclean. Burning off the residue after each cooking will makecleaning easier. Clean with soap a

Parts Diagram - Some small parts may not be depicted.23910121114171513162324272829312522212618203019Description QtyScrew M6 x 15mm 12Wing Bolt M6 x 10

ProblemPossible CauseSolutionGas leaking fromcracked/cut/burnedhose.Damaged hose.Mechanical failure due to rustor mishandling.Failure of valve from mi

Natural Gas supply pressureis lowTROUBLESHOOTING (Cont’d)ProblemFlames blow outFlare upPersistent grease fireUnable to fill LP tankPossible CauseHigh

TROUBLESHOOTING (Cont’d)Although this sound may be alarming, this is NOT dangerousas long as it is not accompanied by the smell of gas. Simplyadjust t

27This page intentionally left blank.

MECO CORPORATIONLIMITED WARRANTYThis product is warranted to the original consumer purchaser against defects in material and workman-ship under normal

7. WARNING! If your grill catches on fire:• If the fire is in the grill portion and you can safelyreach the control knobs, then turn them off by tu

— NOTICE —MECO Corporation strives to be a quality supplier of consumer products. If we ommitted any parts needed for assembly, or you need troublesh

Step 1 - Assemble Wheel LegStep 2 - Assemble Fixed LegTools:Threaded holesOrient Leg.Notice two holesto the front.5Orient wheelswith protrusiontouchin

STEP 3 - Assemble Cart6•Assemble Rear Brace to wheel leg and fixed leg using 4 M6 x 35mm Screws and 4 M6 Nuts.•Assemble the 2 Cart Braces to the wheel

7Install Heat Shieldtoward left side(tank side) of Body.Note orientation of venturitubes to Heat Shield.2341STEP 4 - Attach Flavor Activator Pins, Gre

STEP 5 - Attach Bowl to Cart8•Assemble bowl to cart using 4 M6 x45mm Screws, 4 Fiber Washers, 4Spacers, and 4 M6 Nuts.•Make sure heat shield is restin

STEP6 - Attach Control Panel9STEP 7 - Attach Igniter Wire•Attach Igniter Wire : Push electrode connectorat end of Igniter wire onto center tab on rea