For Customer Service, call 1-800-251-7558 or visit our web site at www.meco.netFOR OUTDOOR HOUSEHOLD USE ONLY. NOT FOR COMMERCIAL USE.• Failure to fol
10STEP9) SIDE BURNER ASSEMBLY:Insert the Side Burner (44) and the Electrode Wire through the front of the large hole in the SideTable. (FIG. 9A) Inst
11STEP 11) BURNER REMOVAL/RE-ASSEMBLY:The Burners (49) are already installed in the grill. There is somecardboard packing underneath each burner; it w
12STEP 13) FLAME DIFFUSER/GRID/ WARMING RACK ASSEMBLY:Lay a Flame Diffuser (54) over each Burner on the lower Bodyridges from front to back. Place eac
13To reduce the risk of serious bodily injury or death:· Use only propane gas in this LP gas grill. · Do not attempt to convert an LP unit to natural
14FIG. 15BHand tighten couplingnut in clockwise directionDisconnecting LP gas cylinder:1) Turn all control knobs to the “off” position and turn the ha
How to perform a leak test:Supplies Needed for a Leak Test: Clean paintbrush, water, and dish washing liquid.1) Use an LP Cylinder equipped with an OP
1. Open the Hood.2. Important: Make sure control knobs are turned “Off”. (FIG. 17B)3. Turn the LP Gas Cylinder valve open counterclockwise until it st
17FIG. 18AFIG. 18BCheck the flame before each cooking session and throughoutthe grilling season. Also check especially after long periods ofstoring th
To reduce the risk of serious bodily injury, death or grilldamage:· Do not cover more than half (50%) the cooking area if using griddle plates. Full c
CARE AND MAINTENANCEA) Drip Tray, Grease Pan, Foil Pan-Loosen the two screws on the sides holding the Drip Tray. Remove and scrape away food and fat r
© MECO CORPORATION®2006— NOTICE —MECO CORPORATION STRIVES TO BE A QUALITY SUPPLIER OF CONSUMER PRODUCTS. IFWE OMITTED ANY PARTS NEEDED FOR ASSEMBLY, O
20Open up main burner holes with a small nail or wire.Wire BrushFIG. 20DTo reduce the risk of a fire beneath the grill:· Inspect and clean burner/vent
21ProblemPossible CauseSolutionBurners will not light using the ignitorBurners not assembledcorrectlyNot holding ignitor switchlong enough for pulse s
22ProblemFlames blow outFlare upPersistent grease fireUnable to fill LP tankHumming orwhistling from theregulatorPossible CauseHigh or gusting windsGa
IMPORTANT NOTICEThe Gas Grill is setup to operate with a LP Gas Cylinder equippedwith an OPD (Overfill Prevention Device).This is a secondary device
P/N 03.6538.00REV. 4/0624MECO CORPORATIONLIMITED WARRANTYThis product is warranted to the original consumer purchaser against defects in material and
3PARTS ILLUSTRATIONSIf you need replacement parts, refer to the Parts Illustrations and the Parts List to find the exact parts you need. If you havean
(53) DRIP TRAY(51) FOIL PAN(54) FLAME DIFFUSER(63) MANIFOLD ASSEMBLY (LP)(60) HEAT INDICATORPARTS LISTITEM DESCRIPTION PART # QTY.1 Owner's Manua
PARTS LIST (Cont'd)31 Bowl Assembly SS/Black 03.6523.00 132 Hood Assembly 430 SS/Silver 03.6524.00 133 Hood Assembly 430 SS/Black 03.6524.01 134
6FIG. 2STEP 3) Front Crossbar Assembly:Turn cart assembly right side up. AttachFront Crossbar (21/22) to side panelswith two M6 x 15 screws into theth
7STEP4) CASTER ASSEMBLY:Lay cart on the floor with Back Panel side down. Assemble Fixed Casters (23) to the LEFT Side ofBottom Panel and Swivel Lock C
STEP 6) HOOD/BOWL TO CART ASSEMBLY:Lift the Hood/Bowl Assembly (30) over the cart assembly and set it down until it rests on theinside top flanges of
9STEP 7) BURNER SIDE TABLE ASSEMBLY:Align the four holes of the LEFT Side Burner Table (36/37)bracket with the threaded inserts in the side of the Bow
Kommentare zu diesen Handbüchern