For Outdoor Household Use Only. Not for Commercial Use.Need Help? Need to Register Your Grill? Looking for Aussie Parts & Accessories?Visit us onl
10 7Step 5Cart Frame AssemblyPlace Rear Leg Frame with Supports and Crossbrace on floor, place Front Leg Frame on top and align holes. Attach Front Le
11Step 7Side Tables to Cart Frame AssemblyAttach the Side Tables to the Legs of the Cart Frame as shown with 8) 1/4-20 x .79” Bolts (4 each Side Table
12Step 9Shroud AssemblyA. Lay the Control Panel and Left, Right and Bottom Shroud Frames face down on floor (on a protective surface). Align brackets
13Step 11Shroud to Cart AssemblyLay the assembled Shroud on the floor with a spacer underneath to keep weight off of the valve stems. Place the cart f
14Step 12A. Wheel Assembly (Model 6623S8Y641)Insert the axle (pre-assembled to wheel) through the sleeve in the bottom of the leg tube. Fasten in plac
15Step 14Drip Cup Wire AssemblySlide the Drip Cup Wire down through the small hole in the center of the bottom of the grill Bowl. (This must be done b
16Step 16Bowl and Cylinder Heat Shield AssemblyAttach the Bowl and Cylinder Heat Shield to the cart with 4) 1/4-20 x .59” Bolts, 4) Fiber Washers and
17Step 17Side Burner Electrode AssemblyA. Insert small end of Electrode Wire down through hole in Side Table until metal tab with hole is seated over
18Step 19A. Main Burner Electrode AssemblyInsert small end of each Electrode Wire down through holes in Bowl in front of main burner until flange of c
19Step 20A. Hood Handle Attach the Hood Handle to the Hood with 2) 1/4-20 x .39” Bolts and Fiber Washers. Place Heat Baffles between the Handle and th
2NOTICEMeco Corporation strives to be a quality supplier of consumer products. If we omitted any parts needed for assembly, or you need troubleshootin
20To reduce the risk of a laceration hazard:• Wear protective gloves when installing warming rack. Hood and Bowl edges could be sharp.CAUTION!Step 22F
21Step 24A. Drip Cup AssemblyInsert the Drip Cup into the hanger wire underneath the grill bowl. B. Cylinder Retainer Wire AssemblyPosition the Cylind
22Connecting/Disconnecting the GasUsing GasCarbon Monoxide Hazard• This appliance can produce carbon monoxide which has no odor. Using it in an enclo
23LP Hose and RegulatorTo reduce the risk of serious bodily injury or death from fire or explosion:• Clean and inspect the gas hose/regulator before e
24Before Using Your LP Gas GrillInstallation CodesTo reduce the risk of serious bodily injury or death from fire or explosion:• This installation must
25How to Perform A Leak Test “FIRST TIME USE” and as requiredSupplies Needed for a Leak Test:• Clean paint brush• Water• Dish washing liquid1. Use an
266. If “growing” bubbles appear on any of the connection points, you have detected a gas leak. Immediately close the LP Gas Cylinder valve by turning
27Lighting the Grill Using the Pulse-Spark Ignitor (continued)1. Open the Hood.2. IMPORTANT: Make sure Control Knobs are turned “Off.” (Fig. 4)3. Turn
28Manually Lighting the GrillTo reduce the risk of serious bodily injury or death from fire or explosion:• Open Hood before lighting the grill to prev
29Lighting the Side BurnerTo reduce the risk of serious bodily injury or death from fire or explosion:• Open Side Burner Lid before lighting the grill
3ContentsPreparation for Assembly ...3Parts IdentificationParts Illustration Model 6623S8E641 ...
30Cooking On the Gas GrillTo reduce the risk of serious bodily injury or death from fire, explosion or burn hazard:• Never use charcoal or lighter flu
31Roasting (Indirect Method)To reduce the risk of burns from the hot air and steam trapped inside:• Open the Hood carefully when roasting on grill.WAR
32Warming RackTo reduce the risk of fire or flare-up from grease drippings:• When cooking food on the warming rack, make sure no Burners are on direct
33Care and MaintenanceCAUTION!Cleaning the GrillRegularly clean your LP gas grill between uses and especially after extended periods of storage. Ensur
34How to Clean the Burners1. Make sure the Control Knobs are turned “Off” and the grill is completely cooled.2. Carefully remove the Warming Rack, Coo
357. Check the Gas Collector Box to verify that there is a 3/16” gap between the electrode tip and the top flange of the box as shown in Fig. 12.Make
36StorageTo reduce the risk of serious bodily injury or death:• Store your LP gas grill in a cool dry place. Do not store an LP Gas Cylinder in a spac
37EmergenciesProblemGas leaking from cracked/cut/burned hoseGas leaking from LP Gas CylinderGas leaking from LP Gas Cylinder valveGas leaking between
38TroubleshootingProblemBurners will not light using a matchLow flame or low heatFlames blow outPossible CauseRegulator coupling nut is not fully conn
39ProblemFlare upPersistent grease fireUnable to fill LP tankHumming or whistling from regulatorPossible CauseGrease build-upExcessive fat in meatGrea
4Parts Illustration - Model 6623S8E641If you need replacement parts, refer to the Parts Illustrations to find the exact parts you need. If you have an
40Limited WarrantyMECO CORPORATION - LIMITED WARRANTYThis product is warranted to the original consumer purchaser against defects in material and work
5Parts List- Model 6623S8E641Key Description Quantity1 Side Burner Cover 12 Side Burner Cooking Grid 13 Side Burner Electrode
6Parts Illustration - Model 6623S8Y641If you need replacement parts, refer to the Parts Illustrations to find the exact parts you need. If you have an
7Parts List- Model 6623S8Y641Key Description Quantity1 Side Burner Cover 12 Side Burner Cooking Grid 13 Side Burner Electrode
8Assembly InstructionsStep 1Front Leg Frame AssemblyIdentify parts and lay on floor as shown. Parts are named for their assembled position on the gril
9NOTE:Threaded Insert on top and nearest rear legsNOTE:notches closest together to outsideRear Leg AssemblyCylinder SupportSide CrossbraceRightBowl Su
Kommentare zu diesen Handbüchern