Aussie®by Meco®LP Gas GrillAssembly and Use ManualJoeyTMFor Customer Service, call 1-800-251-7558 or visit our web site at www.meco.netFOR OUTDOOR HOU
Step 10) Install Cooking Grid:(Note Warming Rack already installed.)Lay Cooking Grid onto the Bowl ridges over theFlame Diffuser and Main Burner. (FIG
11To reduce the risk of serious bodily injury or death:· Use only propane gas in this LP gas grill. · Do not attempt to convert an LP unit to natural
CylinderRetainer ClipCylinderCarry HandleTo avoid pinching in next step, keep fingersand hands near corners of Cylinder RetainerClip when swinging Cli
13To reduce the risk of serious bodily injury or death:· This outdoor cooking appliance shall be used only outdoors and shall not be used in a buildi
141. Open the Hood.2. Important: Make sure all control knobs are turned “Off”. (FIG. 13A)3. Turn the LP Gas Cylinder valve open counterclockwise until
15MANUAL LIGHTING THE GRILL1. Open the Hood.2. Important: Make sure control knobs are turned “Off”. (See FIG. 13A)3. Turn the LP Gas Cylinder valve op
16Closing the Hood forms an ‘oven’ and traps a large amount ofheat for roasting whole meats, chickens, etc. Therefore, it isIMPORTANT that the burner
171) Remove Drip Cup, Cooking Grid, and Flame Diffuser.2) Drip Cup-Wash the Drip Cup with soap and water. 3) Grill Body and Cart-Do not mistake the ac
FIG. 15BWingnutsHeat Shieldedge overCrossbraceedgeScrewsHeat ShieldValve nozzles mustfit inside Burnerventuri tubes .Burner ScrewFIG. 15C5) Use a pipe
19ProblemPossible CauseSolutionGas leaking fromcracked/cut/burnedhose.Damaged hose.Mechanical failure due to rustor mishandling.Failure of valve from
2I. Assembly Instructions...2Parts Illustrations...
20Natural Gas supply pressureis lowTROUBLESHOOTING (Cont’d)ProblemFlames blow outFlare upPersistent grease fireUnable to fill LP tankPossible CauseHig
21TROUBLESHOOTING (Cont’d)Although this sound may be alarming, this is NOT dangerousas long as it is not accompanied by the smell of gas. Simplyadjust
MECO CORPORATIONLIMITED WARRANTYThis product is warranted to the original consumer purchaser against defects in material andworkmanship under normal o
P/N 03.6602.01REV. 20071129Aussie®
3PARTS ILLUSTRATIONSIf you need replacement parts, refer to the Parts Illustrations and the Parts List to find the exact parts you need. If you havean
(35) Flame Diffuser(34) Cooking Grid(37) Fabric Panel(39) LP CylinderHeat Shield(36) Main Burner42) Main BurnerElectrode(40) Control Panelw/Manifold a
5STEP 1) Cart Assembly:Attach the Legs to the Bottom Shelf withM5 x 40 Bolts threaded into the BottomShelf holes. Position legs with the holesexactly
STEP 2) Assemble Axle, Wheels & Wheel Covers:6(10) WHEEL2 PC(12) WHEEL COVER2 PCPush Axle through center hole in Wheel and through lower hole in
Step 4) Install Drip Cup:Insert Drip Cup into Drip Cup Holder ring (installedin bottom of Grill Body) until the cup flange isflush with the ring (17)
8Step 5) Assemble Sidebraces:· Attach Right and Left Sidebraces (19 & 20) to legs with ST4.0 x 10 Screws. (FIG. 5A) Secure Bottom Heat Shield to L
9(27) BOLT, M6X15 8 PC(27) SCREW, M6X15 FIG. 6AFIG. 6B(27) BOLT, M6X15 (26) LEFT SIDETABLE(25) RIGHT SIDETABLEStep 6) Assemble Side Tables:Align brac
Kommentare zu diesen Handbüchern